8076 Positive Displacement Flowmeter

Brand: Burkert Fluid Control Systems

This positive displacement flowmeter with display Type 8076 is designed for use in highly viscous fluid like glue, honey. It is made up of a compact sensor fitting (S070) and an enclosure with cover, containing the electronic module. 

A removable display completes the flowmeter. This ensemble (SE36) is quickly and easily connected to the sensor fitting (S070) by a Quarter-Turn. 

The flowmeter can operate without the display, but it will be required for configuring the flowmeter (i.e. set parameters, restore default parameters, configure information to be displayed, programme access code, adjust 4-20 mA output(s) and also for visualizing continuously the measured and processed data.
Features
  • Configurable outputs: one or two transistor output(s) and single or dual 4-20 mA current output(s)
  • Removable backlit display of flow rate and/or 2 two totalized volumes
  • Automatic-calibration: Teach-In, simulation of outputs signals provided without the need for real flow

Specifications

Ambient Temperature Range

  • Operating & Storage: 0° to 60° C (32° to 140° F)

Approvals & Certifications

  • CE
  • EMC: EN 61000-6-2, EN 61000-6-3
  • PED 97/23/CE
  • UL (C,US): UL 61010-1 + CAN/CSA C22.2 No.61010-1

Cable Length

  • 164 feet (50 metres) - Max.

Circuit Protection

  • Short Circuit Protected for Transistor Outputs

Consumption

  • Current (2 or 3 Outputs Flowmeter [2-Wire]): ≤ 25 mA at 14 Vdc without Transistors Load, with Current Loop
  • Current (4 Outputs Flowmeter [3-Wire]): ≤ 5 mA at 12 Vdc without Transistors Load, without Current Loop
  • Current: ≤ 1 A with Transistor Loads
  • Power: 40 W, Max.

Cover Material

  • Polycarbonate

Current

  • 4-20 mA

Diameter

  • Pipe: 1/2 to 4” (DN 15 to DN 100)

Display

  • Grey Dot Matrix 128 x 64 with Backlighting

Electrical Connectors

  • 1.5 mm², Max.
  • 5-Pin M12 Female
  • Shielded Cable

Electrical Protection

  • Voltage Peak: Protected

Enclosure, Body Material

  • 316L Stainless Steel 1.4401
  • 316Ti Stainless Steel, 1.4542
  • Aluminum
  • PPS

Environmental Protection

  • IP65
  • IP67

Flange Size - 1-1/2” (DN 40)

  • Unrated

Flange Size - 1” (DN 25)

  • Unrated

Flange Size - 2” (DN 50)

  • Unrated

Flange Size - 3” (DN 80)

  • Unrated

Flange Size - 4” (DN 100)

  • Unrated

Humidity

  • ≤ 80 % Relative Humidity, Non-Condensing

Loop Impedance

  • 1 Current Output: 180 ohms at 14 Vdc, Max.
  • 1,100 ohms at 36 Vdc, Max.
  • 2 Current Outputs: 100 ohms at 12 Vdc, Max.
  • 610 ohms at 24 Vdc, Max.

Materials of Construction

  • Display, Quarter-Turn System: Polycarbonate (PC)
  • Fixed Connector Mounting Plate: 316L Stainless Steel, 1.4404
  • Fixed Connector: Brass Nickel-Plated
  • Fixed Connector: Stainless Steel
  • Navigation Key: PBT

Measuring Error

  • Measurement Deviation: ± 0.5 % of Reading

Measuring Range

  • Viscosity 5 MPa.s: 2 to 1,200 L/minute

Operating Voltages

  • 2 or 3 Outputs Flowmeter (2-Wire): 14-36 Vdc, Filtered & Regulated
  • 4 Outputs Flowmeter (3-Wire): 12-36 Vdc, Filtered & Regulated

Output

  • 1 Transistor Output, 2 Transistor Outputs (NPN): 1-36 Vdc
  • 2 Transistor Outputs: 0.5 A, Max.
  • 4-20 mA, 2 & 3-Wire
  • Transistor: 700 mA - Max.

Output Format

  • Open Collector

Pressure Range

  • bar: 0 to 55
  • kPa: 0 to 5,500
  • psi: 0 to 798

Process Temperature

  • Aluminum Body: 0° to 80° C (32° to 176° F)
  • Stainless Steel Body: 0° to 100° C (32° to 212° F)

Repeatability

  • ≤ 0.03 % of Reading

Reverse Polarity Protection

  • Yes

Screw Material

  • Stainless Steel

Seat / Seal Material

  • Seal: EPDM
  • Seal: FEP
  • Seal: FKM
  • Seal: PTFE

Shaft Material

  • Stainless Steel

Shock

  • EN 60068-2-27

Switch Type

  • 1 Transistor Output (NPN), 2 Transistor Outputs (NPN & PNP): Transistor

Vibration

  • EN 60068-2-6

Viscosity

  • 5 MPa ·s
  • 1 Pa·s Max.

Wetted Materials

  • Rotor: 316L Stainless Steel (1.4401)
  • Rotor: Aluminum
  • Rotor: PPS

show more